Iscar's Heliturn system features a unique, double-sided insert with 4 cutting edges for Fast Metal Removal (FMR) turning. The revolutionary Heliturn is a tangentially clamped insert using a specific helical shaped cutting edge, useful for hefty depths of cut and greater than common feed rate. The LNMX...-HT Heliturn insert is screw-clamped into the SLANR tool holder and supported by the TLN ..-HT carbide seat. This seat has ground surfaces on the top and bottom, to ensure perfect contact of the insert with the tool holders. The upper rake face of the insert is mounted level with the top of the tool holder to enable chips to flow across the insert, without being disrupted by clamps or the tool holder body. The 4 curved helical cutting edges establish positive radial rake angles and soft penetration into the metal being cut. The decreased forces and smaller loads insure better tool longevity, higher stability and the ability to use very tremendous depths of cut and larger feeds. The chipformer, distorts and breaks the chip into rib type curved pieces which can immediately be removed from the cutting area. The insert has a frontal clearance angle of 3.7 with a 6 side clearance angle to grant machining to a 90 shoulder. Depth of cut up to .315" and facing depths to .126" at up to .047" IPR are achievable with Heliturn.

When compared to CNMG/M 16... or WNMG/M 13... insert sizes with the identical corner radius, much greater tool life can be predictable when using the LNMX 1506..-HT insert. Iscar has recently included a lesser size to the Heliturn family - the LNMX 1104..R/L-HT insert and tool holder for the medium application range of up to .197" depth of cut. The revolutionary insert features all of the blessings of the larger insert. This increases the economical advantage in the medium machining application extent. When compared to CNMG/M 43. 12... or WNMG/M 43. 08... insert sizes with the same corner radius, a significantly better tool life can be predicted. The inserts are accessible in .031, .047 and .063" tool nose radii. Heliturn inserts are attainable in the most superior carbide grades: IC9025, IC3028 , IC428, IC907, and IC908.

The external tool holders are offered in 1, 1.25 and 1.5" shank sizes. Boring bars are offered in 1, 1.25 1.5 and 2" bar sizes. Also available are exchangeable heads. These tool holders have Iscar's unique Hard Touch coating, which extends holder life and thwarts corrosion. As a result of the positioning of this insert, machining next to the tailstock is conceivable.

The high positive rake angle of these tools allows 10-15% less power consumption/utilization/expenditure than traditional tool holders at the same parameters.

By utilizing Iscar's Heliturn tools, tremendous cost savings and profitability in lathe operations is guaranteed.

A Unique 80 Degree Rhombic Insert with high helical cutting edge for high metal removal rates Iscar is announcing the CNMX 1207..-HTW insert family. The revolutionary insert has a very positive radial, helical cutting edge and a positive rake angle; a succession which extensively reduces the cutting forces. The insert's corner has a wiper arrangement which supplies high surface finish even at high feed conditions, which in many occasions can eliminate a finishing cut. The corner angle is 88 degrees which provides expanded strength. The CNMX inserts were built for heavy machining applications. Their special design ensures dependable, fast metal removal when using 80 degree rhombic inserts. They can be mounted on any conventional tool holder that carries regular CNMG inserts, but the seat has to be substituted with a special seat: TCH 4. Iscar's R-clamp tool holders are highly favored for heavy machining applications.

Easy Methods To Use Your Concrete Cut Off Saw With A Diamond Saw Blade
Are you looking for a multipurpose tool that will do a lot of jobs around the house or job site? A concrete cut off saw will cut more than you think.

Corded Or Cordless Power Equipment - Which Are Regarded The Best?
The DIY and the construction industry or market are awash with power tools of various types and of course financial values.

Saving You Hardware Troubles And Lots Of Cash: Acquiring The Ideal Cordless Drill
Whether you're an avid craftsman or an amateur just looking to fix things around the house, to buy a cordless drill can be a daunting task.

Why People Prefer Digital Caliper.
Here are some of the top reasons for considering a digital caliper. Depending on the size of your requirement you can get a caliper for about $49-100. A battery is used to power the device. It lasts and so you do not have to worry about replacing the battery.

Tips On How To Purchase A Megger Tester
A Megger tester is a device that is commonly used in electrical contracting to determine if the system has been properly installed.